General-tools-and-instruments 861 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Nástroje General-tools-and-instruments 861. General Tools and Instruments 861 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
USERS MANUAL
No. 861
PLEASE READ THESE INSTRUCTIONS FULLY BEFORE USING THIS JIG
FOR MORE INFORMATION AND VIDEO INSTRUCTIONS VISIT
WWW.GENERALTOOLS.COM/DOVETAILER2
THE
DOVETAIL JIG
861 Dovetailer II Manual 11P-081711_Layout 1 8/17/11 5:12 PM Page 1
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - DOVETAIL JIG

USERS MANUALNo. 861PLEASE READ THESE INSTRUCTIONS FULLY BEFORE USING THIS JIGFOR MORE INFORMATION AND VIDEO INSTRUCTIONS VISITWWW.GENERALTOOLS.COM/DOV

Strany 2 - CONTENTS

CUTTING JOINTS LONGER THAN THE JIG OPENINGJoints longer than the opening must be cut in multiple continuous segments. To align the jig withthe previou

Strany 3 - INTRODUCTION

EDGE TO EDGE JOINTING1. When cutting an edge joint, the round-overcreated by the dovetail jig must be eliminated inorder to join the two pieces of woo

Strany 4 - CAPACITY AND SPECIFICATIONS:

CUTTING A BOX JOINT• When cutting a box joint, only use the “TAILS” portion of the jig for all cuts.• For box jointing, use a 1/2 in. diameter straigh

Strany 5 - DOVETAIL JIG ASSEMBLY

• Cut the slots in the first board with the board edge set flush with the right hand edge of thejig. (FIG. 20). Make the entry and exit cuts using the

Strany 6 - PREPARING THE ROUTER

CUSTOMER SUPPORTPlease visit our website at www.generaltools.com/dovetailer2 to obtain additional woodworkinginformation, instructional videos and pro

Strany 7 - CUTTING JOINTS

NOTES_________________________________________________________________________________________________________________________________________________

Strany 8

GENERAL TOOLS & INSTRUMENTS80 White Street, New York,NY10013-3567PHONE (212) 431-6100FAX (212) 431-6499TOLL FREE (800) 697-8665e-mail: sales@gener

Strany 9

CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Capacity and Specifications . . . . . . . .

Strany 10

INTRODUCTIONThank you for purchasing General Tools & Instruments’ DOVETAILERII Dovetail Jig. A simple andeasy way to make professional dovetail jo

Strany 11

CAPACITY AND SPECIFICATIONS:Accommodates stock from 1/2 in. to 1 in. thick.WHAT’S IN THE JIG KIT The fully assembled jig Two router table guide knobs

Strany 12 - “round-over”

ANATOMY OF THE DOVETAILER II JIGDOVETAIL JIG ASSEMBLYNOTE: Your jig comes fully assembled for use. The addition of the router control knobs aids in th

Strany 13 - in from the right hand

USING THE BUILT-IN DEPTH GAUGEThe built-in Depth Gauge is used to set both the depth of the Dovetail Cutter during router setupas well as to control t

Strany 14 - WARRANTY INFORMATION

73. FIG.7 shows the dimension of thedovetail joint affected by the cutterheight.NOTE: Setting this height affects thelength of the Tails and the depth

Strany 15

6. Clamp the board to a workbench orsecure it in a vice as shown (FIG. 10)or if using a router table, make surethe face saying “cut tails this side” i

Strany 16 - 861 User’s Manual

10. Make all cuts to the pins board. For those cuts, the router should ride on the surfacemarked “cut pins this side” shown in FIG. 13 & 14. Be su

Komentáře k této Příručce

Žádné komentáře